| Customization: | Available |
|---|---|
| After-sales Service: | Support |
| Warranty: | Lifetime Warranty |
|
Still deciding? Get samples of US$ 10/Piece
Request Sample
|
Suppliers with verified business licenses
Audited Supplier Audited by an independent third-party inspection agency
DIN 40NiMoCr10-5/1.6745 BS EN26 826M40 Hot Rolled Forged Alloy Steel
826M40 steel is still often referred to as EN26 steel - its equivalent grade under the previous BS 970: 1955 standard.
826M40 grade steel is a 2.5% nickel-chromium-molybdenum through hardening steel which has a high hardenability.
It may be treated in relatively large section sizes to produce tensile strengths ranging from 850 to over 1550 N/mm² combined with good ductility and resistance to stock.
Due to its high molybdenum content, the steel may normally be tempered in the range 300-550C without serious loss of impact values.
Good mechanical properties at low temperature can also be obtained.
Steel equivalent
| Country | Australia | Germany | Britain |
| Standard | X1444 | EN10250 | BS970 |
| Grade | X9940 | 40NiMoCr10-5/1.6745 | EN26/826M40 |
| Grade | C | Si | Mn | P | S | Cr | Mo | Ni |
| EN26 | 0.36-0.44 | 0.1-0.4 | 0.45-0.7 | 0.04 | 0.04 | 0.5-0.8 | 0.45-0.66 | 2.3-2.8 |
| 1.6745 | 0.36-0.44 | 0.1-0.4 | 0.45-0.7 | 0.025 | 0.015 | 0.5-0.8 | 0.45-0.65 | 2.3-2.8 |
| X9940 | 0.36-0.44 | 0.1-0.4 | 0.45-0.7 | 0.025 | 0.015 | 0.5-0.8 | 0.45-0.65 | 2.3-2.8 |
The mechanical properties mainly include tensile strength, yield strength, elongation, area or reduction, hardness, impact value, non-metalic inclusion etc. Different heat treatment, the mechanical properties will be different, such as normalized, tempered, QT. If you want to know the properties, kindly contact the salesman.
overviews
| Size | Round | Dia 6-1200mm |
| Plate/Flat/Block | Thickness 6mm-500mm |
|
| Width 20mm-1000mm |
||
| Heat treatment | Normalized ; Annealed ; Quenched ; Tempered | |
| Surface condition | Black; Peeled; Polished; Machined; Grinded; Turned; Milled | |
| Delivery condition | Forged; Hot rolled; Cold drawn | |
| Test | Tensile strength, Yield strength, elongation, area of reduction, impact value, hardness, grain size, ultrasonic test, US inspection, magnetic particle testing, etc. | |
| Payment terms | T/T;L/C;/Money gram/ Paypal | |
| Trade terms | FOB; CIF; C&F; etc.. | |
| Delivery time | 30-45 days | |
| Application | EN26 alloy steels are used for Axles, Connecting Rods, Die Holders, Hydraulic Shafts, Spindles, Motor Shafts, Pins, Rams, Rolls, Sockets, Tool Holders, Torsion Bars etc.. | |
Heat Treatment
Annealing
Heat to 790 oC - 840 oC, hold until temperature is uniform throughout the section and cool in furnace.
Flame or Induction Hardening
EN26 hardened and tempered bar can be further surface hardened by either the flame or induction hardening methods resulting in a case hardness in excess of Rc 50.
Parts should be heated as quickly as possible to the austenitic temperature range (820 oC - 850 oC) and required case depth followed by an immediate oil or water quench, depending upon hardness required, workpiece size/shape and quenching arrangements.Following quenching to hand warm, most components should be tempered between 150 oC - 200 oC to remove quenching stresses in the case. This will have little effect on case hardness.
Hardening
Heat to 820 oC - 850 oC, hold until temperature is uniform throughout the section, soak for 10 - 15 minutes per 25 mm section, and quench in oil, water, or polymer as required. Temper immediately while still hand warm.
Nitriding
EN26 hardened and tempered bar can also be successfully nitrided, giving a surface hardness of up to Rc 60. Nitriding is carried out at 490 oC - 530 oC, followed by slow cooling (no quench) reducing the problem of distortion. Parts can therefore be machined to near final size, leaving a grinding allowance only. The tensile strength of the core is usually not affected since the nitriding temperature range is generally below the original tempering temperature employed.N.B. Nickel is inert to the action of nitrogen and in general resists its diffusion into steel, and this can result in a lower case hardness or longer nitriding cycle times for steels containing nickel such as EN26.
Stress Relieving
Heat to 640 oC - 660 oC, hold until temperature is uniform throughout the section, soak for 1 hour per 25 mm section, and cool in still air.
Tempering
Re-heat to 450 oC - 660 oC as required, hold until temperature is uniform throughout the section, soak for 1 hour per 25 mm of section, and cool in still air.N.B.Tempering should be avoided if possible within the range 250 oC - 450 oC due to temper brittleness.
Delivery condition
For hot forged rolled bar, usually the delivery condition is hot forged or rolled, annealed/QT, rough turned/Black surface.
For hot forged or hot rolled bar, usually the delivery condition is hot rolled, annealed/QT, Black surface.
For hot forged plate, usually the delivery condition is hot forged, annealed/QT, milled surface/Black surface
For hot rolled plate, usually the delivery condition is hot rolled, annealed/QT, black surface.
| COLD WORK TOOL STEEL | |||||
| Grade | AISI /ASTM | DIN (W.Nr) | JIS | EN/ BS | GB |
| DC53 | higher than D2 | SKD11 | XW-5 | Cr8Mo2Vsi | |
| D2 | D2 | 1.2379 | SKD11 | BD2 | CR12MO1V1 |
| Cr12MoV | CR12MOV | ||||
| D3 | D3 | 1.2080 | SKD1 | BD3 | CR12 |
| O1 | O1 | 1.2510 | SKS3 | 9CRWMN | |
| HMD5 | HMD5 | 7CrSiMnMoV | |||
| 5CrNiMo | L6 | 55NiCrMoV6 | SKT4 | 5CrNiMo | |
| 52100 | 52100 | 1.3505 | EN31 | GCR15 | |
| HOT WORK TOOL STEEL | |||||
| H13 | H13 | 1.2344/1.2342 | SKD61/DAC | 8407 | 4CR5MOSIV1 |
| FDAC | 1.2347 | FDAC | FDAC | ||
| H11 | H11 | 1.2343 | SKD6 | H11 | |
| 3Cr2W8V | H21 | 1.2581/ X30WCrV93 | SKD5 | BH21 | 3CR2W8V |
| PLASTIC MOULD STEEL | |||||
| P20 | P20 | 1.2311 | HPM7/PX88 | 618 | 3CR2MO |
| 718 | P20+NI | 1.2738 | PX4/PX5 | 718 | 3CR2NIMO |
| S136 | 420 | 1.2083 | S-STAR | S136 | 4CR13 |
| NAK80 | P21 /P20+S | 1.2312 | NAK80 | 15NI3MN | |
| HIGH SPEED STEEL | |||||
| M2 | M2 | SKH51 | W6MO5CR4V2 | ||
| M42 | M42 | S2-10-1-8 | SKH59 | W2MO9CR4VCO8 | |
| ALLOY STRUCTURE STEEL | |||||
| Grade | AISI /ASTM | DIN (W.Nr) | JIS | EN/ BS | GB |
| 5120 | 5120 | 1.7027 /21Cr4 | SCr420 | 20Cr | |
| 530M40 /5140 | 530M40 /5140 | 1.7035 /41Cr4 | SCr440 | 40Cr | |
| 5145 | 5145 | Scr445 | 45CR4 | ||
| 4118 | 4118 | 1.7243 /18CrMo4 | SCM418 / SCM420 | 20CrMo | |
| 4135 | 4130 | 1.7218 /25CrMo4 | SCM430 | 708A25/ 708M25 | 30CrMo |
| 4140 | 4140 | 1.7225 /42CrMo4 | SCM440 | EN19/ 709M40 | 42CrMo |
| 4340 | 4340 | 1.6582/ 34CrNiMo6 | SNCM 439/ SNCM8 | EN24/ 817M40 | 40CrNi2Mo |
| 8620 | 8620 | 1.6523/ 21NiCrMo2 | SNCM220 | 805M20 | 20CrNiMo |
| CARBON STEEL | |||||
| 20 | 1020 | C22. CK22 | S20C | EN3B /070M20 | 20 |
| 35 | 1035 | C35.CK35 | S35C | 35 | |
| 45 | 1045 | C45.CK45 | S45C | EN8D/C45E | 45 |
| 50 | 1050 | CK53 | S50C | EN9/070M55 | 50 |
| Q355 | S355J /ST52 | EN14 | Q355 | ||
| 30Mn | 1030.1033 | S30C | 30Mn | ||
| 30Mn2 | 1330 | 30Mn5 | SMn433h | 30Mn2 | |
| STAINLESS STEEL | |||||
| steel grades: 304, 304L, 316, 316L, 321, 410 430, 431, 2205, 2304, 2507. F53, F55 | |||||
){kind=link}